Optimus Prime Transformers RLC Display Assembly Instructions

These instructions are for our folding acrylic Optimus Prime Transformers RLC box display, which has three box displays connected and hinged, with magnetic front panels. 

 

Step 1: Lay out the acrylic panels for each box display
Keep the protective paper film on the acrylic, lay out all the acrylic panels on a clean surface, making sure they are positioned for easy identification.

Important Notes:
Consider using gloves during assembly to prevent fingerprints.

Step 2: Start with the bottom (Panel #1)
To begin, take the bottom panel  (#1) and position it on the surface with the #1 sticker facing up and the door hole towards you. Peel off the top protective film.
 

 

Step 3: Assemble the walls (Panels #2, 3, 4)
Next, remove the paper film from the back (#2) and side panels (#3 & 4). Then, assemble the side panels to the back panels and place them down onto the bottom panel by aligning the tabs and holes. 

 

Important Note: Ensure that any KR logos are right side up and facing outwards. The actual engraving will be on the insides of the side panels. Place these panels on top of the bottom panel (#1) by aligning the tabs and holes.

 

  

 

Step 4: Assemble the Top (Panel #6)
Remove the protective film from the bottom side of the top panel (#6) and place it on top of the other panels, by aligning the tabs and holes.

 

Step 5: Securing the panels together with hardware
Using the acrylic nuts and stainless screws provided, insert one of the nuts into one of the holes on the top of the right side. While holding the nut in place, insert a screw into the screw hole above and start threading into the nut by hand to get it started. Then snug the screw down with the provided hex wrench.

Repeat this process on the left side.

After securely holding the bottom panel in place, carefully flip the display over. Then repeat this process on each side.

 

 

Step 6: Assemble the boxes and hinges
After all the boxes have been assembled, to make things easier for this part, you can lay the large box display face down to start the assembly of the hinges. Then, paying close attention to which way to top and bottom, place one of the smaller boxes on the back side of the larger display and align the hinges of the smaller box within the hinges of the larger box. Then assemble the hinge binding bolt and nut into the hinge holes and tighten them as much as possible. By design, there is enough gap between the binding bolts to allow the hinges to move freely without compression. 

 

Complete the process above to assemble the remaining box and hinges.

 

Note: You can put a dab of elmers glue or threadlock on the binding bolts to avoid any loosening if it is a concern. 

 

 

 

Step 7: Add the final touches
Once the box is built, remove any protective film on the acrylic and clean the display with a microfiber towel for a pristine look.

Cleaning Notes:

Avoid Windex or other harsh chemicals. Opt for an acrylic cleaner or soap and water to maintain the display's appearance. Use soft cloths like microfiber for cleaning, avoiding paper towels.

 

Step 8: Place your items inside each box
Carefully place your item inside the acrylic box display!

 

Step 7: Assemble the front panel (#6)
Remove the protective film from both sides of the front panel and carefully place the front panel on the front of the display by aligning the magnets together. 

Important Note: If the magnets push the panel away, flip it around and try again.

 

Step 8: Enjoy your finished display
Take a moment to appreciate your work! Your acrylic box display is now ready to show off your items.

Step 9: Share your creation
Share photos of your constructed acrylic box display on social media or with friends to present your collectible showpiece with style!

PS: Be sure to tag us so we can see it too!!!

Facebook / Instagram / Tiktok
@kreativerides

 

 

 

Video Example of Individual Box Assembly

 

 

Video Example of Box and Hingle Assembly