Loosie Diecast Wall Display Assembly Instructions

Important Notes:
Please consider these instructions as a general guide to help with assembly; you may find other tricks or steps to help you. So you do not have to strictly follow the guide below.   

Consider using gloves during assembly to prevent fingerprints.

Step 1: Lay out the acrylic panels
Keep the protective paper film on the acrylic. Lay out all the acrylic panels on a clean surface, ensuring they are positioned for easy identification.

Step 2: Start with the back (Panel #1)
To begin, take the back panel and position it with the #1 sticker facing away from you, then peel each corner back past the alignment tabs and fold them flat. This will help keep the back side protected and still allow you to assemble the display, then peel the film off after the assembly is complete. Next, turn the back panel around and peel the protective film from the front side completely. 
  

Step 3: Prep the shelves and dividers
Next, remove the paper film from each shelf panel (#2) and each divider panel (#3). Stand each shelf up and place one divider on top of them by aligning the slots. This will hold the shelves up and allow you to place each remaining divider.

Step 4: Bottom Panel (Panel #4) and Side Panels (Panel #5 & #6)
Peel the film from the side with the #4 on it, this should be the top side of the panel, the countersunk holes for the screws will be the bottom side. Next, peel the film from the side panels (#5 & 6). Then, ensuring that the KR logos are on the top side of the side panels and facing outwards (The actual engraving will be on the insides of the side panels).  Assemble the side panels to the back panel and the shelves on each side by aligning the holes and tabs. Then assemble the bottom panel to the back panel, side panels, and dividers by aligning the holes and tabs. Using the screws and nuts provided, secure only the side panels to the bottom panel for now. You can easily secure the divider panels later.

Step 5: Assemble the Top (Panel #7)
Remove the bottom protective film from the top panel (#6) and place it on top of the other panels by aligning the tabs and holes. The secure each side panel using the provided screws and nuts.
 

Step 6: Securing the divider panels together with hardware
After the corners have been secured, turn the display vertically on one side. Using the remaining acrylic nuts and stainless screws provided, insert each nut into the holes of each divider. Since the display is vertical, you should be able to easily drop the nuts into each hole. The while holding the nut in place, insert a screw into the related screw hole and start threading into the nut by hand to get it started. Then snug the screw down with the provided hex wrench. DO NOT OVER TIGHTEN!!!

Repeat this process until each side of each divider has been secured.

Step 7: Mounting to a wall
Use a level to align your display on the wall, then mark your holes. Predrill your screw holes and determine if you need anchors to hold your screws. If you need the anchors, secure those first. Then insert your screws, leaving the screw heads approximatly 1/4" (6mm) from the wall. 

Remove the remaining protective film from your display and hang it on the wall!

CAUTION: When mounting the display to the wall, make sure you do not tighten the screws all the way to the wall, this could break your back panel on the display. 

Step 8: Add your items and front panel (Panel #8)
Next, add your items into each slot. Once done, you can peel and remove the film from the front panel (#8) and place it onto the display by aligning the magnets. If the front cover pushed away from the display, flip it over and try again; the magnets must be in the correct orientation to attract each other. 

Step 8: Enjoy your finished display
Remove any remaining protective film and take a moment to appreciate your work! Your acrylic box display is now ready to show off your items.

Cleaning Notes:
Avoid Windex or other harsh chemicals. Opt for an acrylic cleaner or soap and water to maintain the display's appearance. Use soft cloths like microfiber for cleaning, avoiding paper towels.

Step 9: Share your creation
Share photos of your constructed acrylic box display on social media or with friends to present your collectible showpiece with style!

PS: Be sure to tag us so we can see it too!!!

Facebook / Instagram / Tiktok

@kreativerides

Video Example of Assembly